Remeha Avanta Plus P420 Bedienerhandbuch

P 420Fuel oil/gas boilersRemehaAssembly Instructions300016854-001-AEN63193

10P 420 02/04/08 - 300016854-001-A9 Fitting the upper and lower assembly rods and the upper casing supports(1) Front - (2) Rear- Fit the upper assembl

1102/04/08 - 300016854-001-A P 42010 Hydraulic testAfter assembling the boiler body, the installer must carry out a water tightness test at a pressur

12P 420 02/04/08 - 300016854-001-A11- Secure the flue gas nozzle (boiler body accessories) to the flue gasbox (package CS 20) using 4 screws HM 12 x40

1302/04/08 - 300016854-001-A P 42012Fit the 2 threaded rods using multiple slip joint pliers (bodyaccessories package) M12x175 for the flue gas outle

14P 420 02/04/08 - 300016854-001-A13Put in place the lower plug and the upper plug with the sensortube (boiler body accessories package).Do not forge

1502/04/08 - 300016854-001-A P 42015Affix the added hinge (boiler body accessories package) to thedoor of the combustion chamber using the 3 screws H

16P 420 02/04/08 - 300016854-001-A16 Assembling the baffle plates Boilers for following countries: NL - BE - ES Boilers for following countries: GB

1702/04/08 - 300016854-001-A P 42017 Boilers supplied with an assembled body. (1) Rear- Unscrew the screw A on the bracket.ZTo fit the flow controller

18P 420 02/04/08 - 300016854-001-A19` Insert the rear insulation - Package R B2.20Boilers supplied with an assembled body: Fit the upper crosspieces

1902/04/08 - 300016854-001-A P 42021 Control panel assembly(1) Front - (2) RearPosition the control panel in the rear bushes.Open the control pane

2P 420 02/04/08 - 300016854-001-A1 Package listPackage list : Before starting to assemble the boiler, refer to the table below to check if you have re

20P 420 02/04/08 - 300016854-001-A24 Casing assemblyPosition the front side panels (length 520 - Package RB2) in thelower casing supports and hook th

2102/04/08 - 300016854-001-A P 42026Position the front and rear covers in the order shown in thediagram.The intermediate and rear covers are narrowe

22P 420 02/04/08 - 300016854-001-A27 Assembly of the rear panels Package RB2Hook the lower rear panel  to the 2 bushes on the side panels.Put in pla

2302/04/08 - 300016854-001-A P 42029Hook the lower left and right front panels to the bush on the side panel.Hook on the front casing support (2 bus

© CopyrightAll technical and technological information contained in these technical instructions, as well as anydrawings and technical descriptions su

302/04/08 - 300016854-001-A P 4202 Boilers supplied with an assembled body Manoeuvring the assembled boiler bodyTo manoeuvre the assembled body, it

4P 420 02/04/08 - 300016854-001-A Boilers supplied with an assembled body• Hydraulic test: Refer to view 10Certain parts will have to be removed to c

502/04/08 - 300016854-001-A P 4201 Assembly of the base frame, delivered unassembledM0012331M0012342233

6P 420 02/04/08 - 300016854-001-A2 Fitting the brackets Front - RearP 420-8 - P 420-10 - P 420-12 - P 420-14 P 420-9 - P 420-11 - P 420-13 ` Fit t

702/04/08 - 300016854-001-A P 4204Handle the nipples with gloves, there might be sharpedges.- Clean the bores and nipples. Coat with the lubricant su

8P 420 02/04/08 - 300016854-001-A6 Assembling the sectionsA : ThermocordSpecial intermediate section in front of rear section.Place the first specia

902/04/08 - 300016854-001-A P 4207- Put the assembly tool in position.- Tighten gradually so as to bring together the upper and lower connections even